High Silica / Quartz — Vitreous Silica & Fused-Quartz Braided Insulation
Inorganic high-silica and fused-quartz braided textile insulations engineered for extreme +700°C to +1200°C furnace, kiln, metallurgy and turbine temperature sensing.
What are High Silica & Quartz insulations?
Once continuous operating temperatures exceed the ~480°C softening limit of standard E-glass fiberglass, extreme-heat thermocouple and heater leads transition to leached vitreous high-silica (>96% SiO₂) and ultra-pure fused-quartz (>99.9% SiO₂) braided yarns finished with high-temperature resin binders. These non-combustible inorganic braids maintain physical separation between conductors even after initial surface binder bake-out at extreme heat.
High-silica textile braids typically cover +700°C to +900°C continuous environments (peaks to +1000°C), while pure fused-quartz braids extend continuous furnace, heat-treating, metallurgy and exhaust-testing sensing toward +1050°C to +1200°C.
Above +550°C, matching conductor metallurgy is just as critical as selecting the fibre braid. While thermocouple loops use calibration-matched high-temperature alloys (such as Types K, N, R or S), extreme-heat power and cartridge-heater leads require Pure Nickel 200 conductors (ASTM B160) because copper cores oxidise rapidly at furnace temperatures. Because Pure Nickel has ~18%–22% IACS conductivity (roughly 5× copper's room-temperature resistance), engineers typically step up two to three AWG sizes or transition to copper via high-temperature nickel splices outside the hot zone.
Because inorganic silica and quartz braids are porous textiles rather than sealed polymers, they function as dry thermal-spacing barriers and must be protected from conductive liquids. During initial ramp-up above ~300°C, the handling resin binder bakes off cleanly (provide ventilation on first energisation), and an outer SS304 stainless-steel braid is recommended where sharp furnace edges or heavy abrasion exist.
Key Material Properties
| Property | Rating | Notes |
|---|---|---|
| Temperature | +700°C to +1200°C (grade dependent) | Exceeds E-glass and mica-only limits |
| Composition | High-purity amorphous SiO₂ fibres | Non-combustible inorganic braid |
| Dielectric role | High-temp dry spacing barrier | Best kept dry at ambient prior to bake-out |
| Typical uses | High-temperature thermocouple cables | Heat-treating furnaces, kilns & turbines |
| Conductor pairing | Pure Nickel 200 (ASTM B160) · TC alloys | Account for ~5× DCR vs. Cu on Pure Nickel power runs |
| Mechanical & Moisture | Optional SS304 overbraid · Dry service | Porous textile; binder bakes out cleanly on first heat |
Frequently Asked Questions
- What is the difference between High Silica and Quartz thermocouple insulation?
- High Silica (>96% SiO₂) typically covers continuous sensing around 700°C–900°C, whereas pure fused Quartz (>99.9% SiO₂) raises continuous thermal endurance to 1050°C–1200°C for extreme furnace and metallurgical duty.
- Why are high-silica and quartz braids impregnated with silicone resin?
- The resin finish improves abrasion resistance, limits fraying during stripping and slows ambient moisture wicking before the cable enters high-temperature operation.
- Why do high-silica and quartz heater leads above 550°C require Pure Nickel conductors instead of plated copper?
- Even 27% nickel-coated copper reaches its reliable oxidation ceiling around 450°C–550°C. Above 550°C, Pure Nickel 200 (ASTM B160) prevents copper diffusion and strand embrittlement — though engineers must upsize the conductor gauge or limit Pure Nickel to short hot-zone tails due to its lower conductivity (~18%–22% IACS).
- Can high-silica or quartz braided cables operate submerged in water or oil?
- No — vitreous silica and quartz braids are porous inorganic fibres designed for dry extreme-heat spacing. Moisture or conductive coolants can wick into the braid and lower ambient insulation resistance prior to high-temperature drying; keep cold ends sealed and add SS304 braiding for mechanical protection.
Engineering Guides
- PFAS-Free High-Temperature Wire & Cable Alternatives: Navigating ECHA's November 2026 Opinions, EPA TSCA 8(a)(7), and Fluoropolymer Substitution — Following ECHA's November 2026 final PFAS opinions and US EPA TSCA 8(a)(7) updates, learn how to audit PTFE, FEP, PFA, and ETFE wire BOMs and evaluate PFAS-free PEEK, Silicone, Polyimide, XLPO, and Mica alternatives.
- High-Temperature Conductor Selection (150°C to 1000°C+): Tin, Silver, 2% Nickel, 27% Nickel-Coated & Pure Nickel — Why copper oxidizes and forms brittle intermetallics at elevated temperatures — and how to match ASTM B33, B298, B355 (Class 2 & 27), and B160 conductor metallurgies to operating temperature, DCR voltage drop, and permanent termination methods.