Polyimide (PI) — Aromatic Polyimide Film Insulation
Ultra-thin wrapped aromatic polyimide tape — delivering −190°C cryogenic stability to +260°C continuous endurance, high radiation tolerance and minimal finished cable profile.
What is Polyimide insulation?
Polyimide (PI, commonly referenced by trade designations such as Kapton®, a registered trademark of DuPont de Nemours, Inc.) is an aromatic polymer film helically wrapped and heat-sealed around conductors where space, weight and extreme thermal margins are critical. Unlike conventional extruded plastics that melt or turn brittle at extremes, polyimide preserves dielectric and mechanical integrity from −190°C cryogenic environments up to +260°C continuous duty and short-term peaks above +300°C.
Because wrapped polyimide tape achieves high breakdown voltage in ultra-thin walls, it produces slim, low-thermal-mass constructions ideal for composite autoclave cure monitoring, vacuum chambers, aerospace thermal testing, radiation zones and compact thermocouple probes.
Electrically, aromatic polyimide exhibits a dielectric constant of roughly 3.4–3.5 with exceptional dielectric breakdown strength per micron, minimal outgassing in high-vacuum chambers and strong stability under cumulative gamma radiation. Because it is helically tape-wrapped rather than melt-extruded, finished wire profiles remain exceptionally slim and low in thermal mass for precision sensor routing.
Two material caveats govern specification: first, while pure polyimide is halogen-free and PFAS-free, many commercial heat-sealed polyimide tapes incorporate a thin FEP adhesive layer — so strict PFAS-free programmes must verify non-FEP bonding or evaluate extruded PEEK; second, polyimide is sensitive to prolonged strong-alkaline hydrolysis and wet arc-tracking unless protected by a fluoropolymer outer wrap (PTFE/PI) in exposed damp environments.
Key Material Properties
| Property | Rating | Notes |
|---|---|---|
| Temperature | −190°C to +260°C (peaks >300°C) | Cryogenic through high-temp curing |
| Wall profile | Ultra-thin wrapped film | Minimal cable O.D. & low thermal mass |
| Mechanical & Radiation | High cut-through & gamma stability | Non-melting thermoset-like film |
| Typical uses | Thermocouple wire, aerospace, nuclear sensors | Autoclaves, vacuum & tight probe routing |
| Dielectric & Vacuum | εr ~3.4–3.5 · Low outgassing | High breakdown strength per thin wrapped layer |
| PFAS & Hydrolysis | Verify non-FEP bond for strict PFAS-free | Protect against strong alkalis & wet arc-tracking |
Frequently Asked Questions
- Why choose Polyimide over FEP or PFA for thermocouple and aerospace wire?
- Polyimide film enables a much thinner wall and slimmer profile than extruded fluoropolymers while handling −190°C cryogenic to +260°C/+315°C thermal cycles and substantially higher radiation doses.
- Is polyimide thermocouple wire suitable for composite autoclaves?
- Yes — ultra-thin polyimide thermocouple cable routes cleanly beneath vacuum-bag seals without distorting composite layups during elevated-temperature cure cycles.
- Is wrapped Polyimide wire automatically 100% PFAS-free?
- Pure polyimide film contains no fluorine, but many standard heat-sealed polyimide wire tapes use a thin FEP fluoropolymer bonding layer to seal the helical overlap. For strict PFAS-free mandates, request verification of non-FEP sealing or specify 100% PFAS-free extruded PEEK insulation.
- How do Polyimide film and extruded PEEK compare for radiation and +260°C environments?
- Both operate to +260°C with strong gamma-radiation stability. Polyimide film delivers the thinnest wall, lowest thermal mass and −190°C cryogenic range for autoclave and vacuum sensors, whereas melt-extruded PEEK provides a seamless moisture- and steam-proof wall with superior resistance to alkaline hydrolysis and wet arc-tracking.
Engineering Guides
- PFAS-Free High-Temperature Wire & Cable Alternatives: Navigating ECHA's November 2026 Opinions, EPA TSCA 8(a)(7), and Fluoropolymer Substitution — Following ECHA's November 2026 final PFAS opinions and US EPA TSCA 8(a)(7) updates, learn how to audit PTFE, FEP, PFA, and ETFE wire BOMs and evaluate PFAS-free PEEK, Silicone, Polyimide, XLPO, and Mica alternatives.