PVDF — Polyvinylidene Fluoride Insulation
Hard, abrasion- and cut-through-resistant fluoropolymer widely specified for solid wire-wrap backplanes, PCB jumpers and compact high-density electronic assemblies.
What is PVDF insulation?
Polyvinylidene fluoride (PVDF, commonly known by trade designations such as Kynar®, a registered trademark of Arkema Inc.) is a semi-crystalline engineering fluoropolymer prized for exceptional resistance to sharp-edge cut-through, cold flow and mechanical abrasion at ultra-thin wall thicknesses. Those properties established PVDF as the benchmark insulation for solid tinned-copper wire-wrap terminations around square backplane posts where softer polymers split or creep under contact pressure.
Because PVDF is a polar semi-crystalline fluoropolymer, its dielectric constant (εr 7.0–8.5) is substantially higher than non-polar fluoropolymers such as PTFE, FEP or ETFE (2.0–2.6). That makes PVDF ideal for DC and low-frequency backplane wire-wrap leads (such as UL 1423), PCB jumpers and cut-through-resistant outer protective jackets over lower-capacitance cores, while ruling it out as a primary dielectric for high-frequency RF or low-capacitance differential data pairs.
Like ETFE, PVDF resists radiation degradation much better than PTFE/FEP and can be cross-linked for elevated thermal stability up to +150°C in specialty formulations. Its hard surface resists mineral acids, hydrocarbons and board-wash flux solvents without swelling or softening during automated harness processing.
Key Material Properties
| Property | Rating | Notes |
|---|---|---|
| Temperature | Up to +105°C typical | Style-dependent under UL 758 |
| Mechanical | High cut-through resistance | Resists sharp-corner cold flow |
| Wall thickness | Ultra-thin (0.10–0.15 mm) | High-density board & backplane routing |
| Chemicals | Solvent & acid resistant | Withstands assembly cleaning fluids |
| Dielectric constant | εr ~7.0–8.5 (polar fluoropolymer) | For DC/low-freq & protective skins — not GHz RF |
| Typical styles | UL 1423 wire-wrap · Specialty jackets | Pairs cleanly with solid/stranded tinned or SPC |
Frequently Asked Questions
- Why is PVDF preferred for wire-wrap and PCB jumper wire?
- Its high modulus and cut-through resistance prevent insulation splitting on sharp square terminal posts even at 0.10 mm wall thickness, while stripping cleanly without nicking fine solid conductors.
- Is PVDF classified as a fluoropolymer?
- Yes — PVDF is a melt-extrudable fluoropolymer combining strong chemical resistance and inherent flame retardancy with superior mechanical hardness.
- Why is PVDF unsuitable as primary insulation for high-frequency data or RF coaxial cables?
- PVDF has a high dielectric constant (εr 7.0–8.5) and higher dissipation factor than PTFE, FEP or Foam PE, which causes excessive capacitance and signal attenuation at megahertz-to-gigahertz frequencies. Use PTFE, FEP or cellular PE for high-speed signal dielectrics, reserving PVDF for DC/control wire-wrap or outer mechanical skins.
- How does PVDF compare to ETFE for compact electronics wiring?
- PVDF offers extreme surface hardness and thin-wall cut-through resistance at economical cost up to +105°C–+150°C (making it standard for solid wire-wrap), whereas ETFE provides much lower dielectric constant (εr 2.5–2.6), higher flexibility and up to +200°C thermal ratings in cross-linked aerospace grades.
Engineering Guides
- Fluoropolymer vs. Silicone Insulation Guide: PTFE, FEP, PFA, ETFE, PVDF & SiR Tradeoffs — How to choose between extruded/wrapped PTFE, melt-processable FEP and PFA, mechanically tough ETFE and PVDF, and ultra-flexible Silicone Rubber across chemical immersion, bend radius, cut-through, max O.D., HV corona, and 2026 PFAS strategy.