PEEK — Polyether Ether Ketone Insulation
Ultra-high-performance aromatic polymer rated to +260°C continuous — combining extreme tensile and cut-through strength, gamma-radiation tolerance and inherent zero-halogen UL 94 V-0 flame performance.
What is PEEK insulation?
Polyether ether ketone (PEEK) is a semi-crystalline aerospace, nuclear and downhole engineering polymer rated for continuous operation up to +260°C with short-term excursions above +300°C. Unlike standard fluoropolymers, PEEK pairs extreme thermal endurance with extraordinary tensile strength, abrasion and cut-through resistance, minimal cold flow, and high tolerance to gamma radiation, superheated steam and hydrolysis.
Inherently halogen-free and achieving UL 94 V-0 self-extinguishing performance at thin walls without halogenated additives, PEEK constructions (such as CASPEEK 260) serve nuclear instrumentation, aerospace actuators, downhole oil/gas sensors and high-density industrial systems where PTFE creeps or degrades under radiation.
With a crystalline melting point near 343°C and a dielectric constant of roughly 3.2–3.3, PEEK is 100% PFAS-free while matching the +260°C continuous ceiling of PTFE. Paired with silver-plated copper (ASTM B298, up to 200°C) or 2% nickel-plated copper (ASTM B355 Class 2, up to 260°C), melt-extruded PEEK achieves uniform concentric walls across single-core hook-up wire, shielded twisted pairs and multicore instrumentation cables.
Engineers should weigh two practical trade-offs against PTFE and silicone: PEEK is stiffer (requiring a larger minimum bend radius than supple silicone or FEP) and has higher permittivity than PTFE (εr 2.0–2.1), making PTFE or FEP preferable for ultra-low-loss GHz RF coaxial dielectrics while PEEK dominates radiation, clamp-load, cut-through and PFAS-free +260°C designs.
Key Material Properties
| Property | Rating | Notes |
|---|---|---|
| Temperature | −65°C to +260°C continuous | Short-term excursions >300°C |
| Mechanical | Extreme tensile & cut-through | Minimal cold flow vs. PTFE |
| Fire & Chemistry | UL 94 V-0, IEC 60754-2 halogen-free | Radiation, steam & solvent resistant |
| Typical uses | Nuclear, aerospace, downhole, extreme industrial | Weight- & space-critical extreme duty |
| Dielectric & Melt | εr ~3.2–3.3 · Melt ~343°C | 100% PFAS-free semi-crystalline aromatic polymer |
| Conductor pairing | SPC (200°C) · 2% NPC (250°C–260°C) | ASTM B298 / ASTM B355 Class 2 matched to temp |
PEEK Insulated Products
- CASPEEK 260 — ASTM B355 / ASTM B298 / IEC 60754-2 / UL 94 V-0 · PEEK · -65°C to +260°C · 300V
Applications & Standards Using This Material
Frequently Asked Questions
- When should engineers choose PEEK over PTFE?
- Choose PEEK when a +260°C thermal budget is combined with heavy mechanical vibration, high pinch or cut-through loads, ionising radiation exposure or strict zero-halogen mandates.
- Is PEEK inherently halogen-free?
- Yes — PEEK contains no halogens and meets IEC 60754-2 / EN 60754-2 zero-halogen requirements while maintaining UL 94 V-0 self-extinguishing flame behaviour.
- Is PEEK a PFAS-free alternative to PTFE and PFA at +260°C?
- Yes — PEEK contains zero fluorine or halogens and is 100% PFAS-free, matching PTFE's +260°C continuous thermal rating while adding superior cut-through toughness, anti-creep clamp stability and gamma-radiation endurance (with a stiffer bend radius and higher εr ~3.2–3.3 than PTFE).
- What conductor plating should be paired with PEEK insulation for 260°C operation?
- Specify 2% nickel-plated copper (ASTM B355 Class 2) for continuous +250°C to +260°C operation, or silver-plated copper (ASTM B298) when operating up to +200°C with high conductivity and clean solderability.
Engineering Guides
- PFAS-Free High-Temperature Wire & Cable Alternatives: Navigating ECHA's November 2026 Opinions, EPA TSCA 8(a)(7), and Fluoropolymer Substitution — Following ECHA's November 2026 final PFAS opinions and US EPA TSCA 8(a)(7) updates, learn how to audit PTFE, FEP, PFA, and ETFE wire BOMs and evaluate PFAS-free PEEK, Silicone, Polyimide, XLPO, and Mica alternatives.
- High-Temperature Conductor Selection (150°C to 1000°C+): Tin, Silver, 2% Nickel, 27% Nickel-Coated & Pure Nickel — Why copper oxidizes and forms brittle intermetallics at elevated temperatures — and how to match ASTM B33, B298, B355 (Class 2 & 27), and B160 conductor metallurgies to operating temperature, DCR voltage drop, and permanent termination methods.
- Fluoropolymer vs. Silicone Insulation Guide: PTFE, FEP, PFA, ETFE, PVDF & SiR Tradeoffs — How to choose between extruded/wrapped PTFE, melt-processable FEP and PFA, mechanically tough ETFE and PVDF, and ultra-flexible Silicone Rubber across chemical immersion, bend radius, cut-through, max O.D., HV corona, and 2026 PFAS strategy.