PA (Nylon) — Polyamide Insulation & Protective Jacket

High-modulus engineering polymer delivering exceptional cut-through, abrasion and hydrocarbon resistance for thin-wall automotive harnesses and protective outer overjackets.

What is PA (Nylon) insulation?

Polyamide (PA, including PA12 and nylon grades) is a tough, semi-crystalline engineering thermoplastic chosen whenever mechanical cut-through, pinch resistance and fuel/oil barrier protection are paramount. Its hard, low-friction surface supports ultra-thin protective skins or standalone primary insulation (such as ISO 19642 FLR4Y) that pull cleanly through tight conduits and resist sharp metal edges.

When polyamide serves as an extruded protective nylon skin over PVC cores (as in UL 83 THHN/THWN building wire or PVC/Nylon equipment wire), PVC provides primary electrical flexibility while PA forms the outer mechanical and hydrocarbon barrier.

Not all polyamides behave identically in wire and cable engineering. Shorter-chain nylons (PA6 and PA66) provide economical, high-lubricity extruded skins over PVC building and tray-cable cores (such as UL 83 THHN/THWN-2 and UL 1277 Type TC), but absorb more ambient moisture than long-chain grades. By contrast, PA12 exhibits very low moisture uptake, superior sub-zero impact strength and strong resistance to zinc-chloride road-salt stress cracking — making PA12 the preferred standalone thin-wall insulation for ISO 19642 FLR4Y automotive underbody and hydraulic harnesses.

Inherently halogen-free and 100% PFAS-free, polyamide is chosen whenever high scrape abrasion, pinch protection, conduit pull-lubricity and hydrocarbon fuel resistance are required without stepping up to fluoropolymer cost.

Key Material Properties

PropertyRatingNotes
MechanicalHigh cut-through & crush strengthHard, low-friction surface
FluidsExcellent fuel, oil & solvent barrierResists automotive hydrocarbons
TemperatureUp to +125°C (PA12 grades)Grade dependent
Typical usesThin-wall automotive wire, protective overjacketsAbrasion- & pinch-critical routing
Grade selectionPA12 (standalone thin-wall) · PA6/66 (over-skin)PA12 offers low moisture uptake & salt-crack resistance
Compliance & FrictionHalogen-free · 100% PFAS-free · Low frictionEases tight conduit & harness bundle pulling

PA (Nylon) Insulated Products

  • FLR4Y — ISO 19642-3 · PA (Polyamide) · 100°C · 25/60V

Applications & Standards Using This Material

Frequently Asked Questions

When is standalone PA insulation used versus PVC with a Nylon jacket?
Standalone PA (such as FLR4Y) is used when a single-layer halogen-free thin wall with maximum mechanical toughness is required; PVC/Nylon pairs flexible PVC core insulation with a thin extruded nylon protective skin.
Does polyamide resist gasoline, diesel and industrial oils?
Yes — polyamides exhibit strong barrier resistance to fuels, lubricants, hydraulic fluids and many industrial solvents.
What is the difference between PA12 and PA6/PA66 nylon in wire and cable applications?
PA12 absorbs far less moisture than PA6 or PA66, maintaining tighter dimensional stability, cold-impact toughness and resistance to road-salt stress cracking — making PA12 standard for standalone thin-wall automotive wires (FLR4Y). PA6 and PA66 are commonly extruded as thin protective outer skins over PVC cores in UL 83 THHN/THWN-2 building wire.
Why is a thin nylon jacket extruded over PVC on UL 83 THHN and UL 1277 tray-cable cores?
The thin polyamide skin adds a hard, slippery abrasion barrier that cuts conduit pulling friction and shields the softer PVC insulation from gasoline, mineral oils and sharp tray edges without noticeably increasing outer diameter.