AS 22759 — Aerospace Fluoropolymer Airframe & Equipment Wire
Slash-sheet aerospace wire specification (superseding MIL-W-22759) defining lightweight PTFE, ETFE and cross-linked XL-ETFE insulations with tin-, silver- or nickel-plated copper and copper-alloy conductors.
Standard · SAE International (Aerospace)
What is AS 22759?
SAE AS 22759 (superseding legacy MIL-W-22759) is the premier international aerospace specification series for insulated single-conductor wire across commercial aircraft, rotorcraft, defence platforms and avionics. Each slash sheet (such as /10, /11, /12, /16, /18, /32, /34 and /41–/46) fixes conductor plating, alloy strength, insulation chemistry, wall thickness and temperature class from 150°C to 260°C.
Engineers select across three core insulation families: sintered or extruded PTFE for 200°C–260°C chemical immunity; extruded ETFE for mechanical cut-through toughness; and radiation cross-linked XL-ETFE for ultra-lightweight 150°C–200°C airframe harnesses.
Because each slash sheet locks one exact conductor-and-insulation pairing, engineers must cite the full designation rather than generic AS 22759 — for example, AS22759/11 pairs extruded PTFE with 200°C silver-plated copper, AS22759/12 upgrades to 260°C nickel-plated copper, AS22759/16–/19 specify 150°C tin-plated copper or high-strength copper alloy with extruded ETFE, and AS22759/32–/35 and /41–/46 specify radiation cross-linked XL-ETFE across 150°C and 200°C tiers.
Single-conductor AS 22759 wires also serve as the primary insulated cores inside SAE AS 27500 (formerly MIL-C-27500) shielded and jacketed aerospace multicore cables. Where formal NAVAIR QPL/QPD listing or platform-specific qualification paperwork is mandated, confirm exact slash-sheet and gauge qualification requirements at RFQ.
Key Technical Requirements
| Parameter | Requirement | Notes |
|---|---|---|
| Voltage rating | 600V AC RMS typical (1000V on /9–/10) | Thin-, normal- and medium-wall slash sheets |
| Insulations | PTFE · ETFE · XL-ETFE · Polyimide/PTFE | Slash-sheet specific |
| Conductors | TPC · SPC · NPC & High-Strength Alloy | Matched to 150°C, 200°C or 260°C class |
| Performance | Abrasion, fluid & arc-track resistant | Tight O.D. control and low weight per metre |
| Key slash sheets | /11 & /12 (PTFE) · /16–/19 (ETFE) · /32–/35 & /41–/46 (XL-ETFE) | Each slash sheet fixes plating, wall & temp class |
| Multicore pairing | Core component for SAE AS 27500 | Shielded & jacketed aerospace cable assemblies |
AS 22759 Products
- XE150-P — AS 22759 · XL-ETFE · -65°C to +150°C · 600V
- XE150-L — AS 22759 · XL-ETFE · -65°C to +150°C · 600V
- SAE AS22759/43 — AS 22759 · XL-ETFE · -55°C to +200°C · 600V
- SAE AS22759/41 — AS 22759 · XL-ETFE · -55°C to +200°C · 600V
- SAE AS22759/34 — AS 22759 · XL-ETFE · -55°C to +150°C · 600V
- SAE AS22759/33 — AS 22759 · XL-ETFE · -55°C to +200°C · 600V
- SAE AS22759/32 — AS 22759 · XL-ETFE · -55°C to +150°C · 600V
- SAE AS22759/19 — AS 22759 · ETFE · -55°C to +150°C · 600V
- SAE AS22759/18 — AS 22759 · ETFE · -55°C to +150°C · 600V
- SAE AS22759/17 — AS 22759 · ETFE · -55°C to +150°C · 600V
- SAE AS22759/16 — AS 22759 · ETFE · -55°C to +150°C · 600V
- SAE AS22759/12 — AS 22759 · PTFE · -55°C to +260°C · 600V
- SAE AS22759/11 — AS 22759 · PTFE · -55°C to +200°C · 600V
- SAE AS22759/10 — AS 22759 · PTFE · -55°C to +260°C · 1000V
- SAE AS22759/9 — AS 22759 · PTFE · -55°C to +200°C · 1000V
Insulation Materials in This Standard
Frequently Asked Questions
- What is the difference between AS22759/11, /12, /16 and /32?
- AS22759/11 uses extruded PTFE with silver-plated copper (200°C, 600V), while AS22759/12 uses extruded PTFE with nickel-plated copper (260°C, 600V). AS22759/16 uses non-cross-linked extruded ETFE with tin-plated copper (150°C), and AS22759/32 uses lightweight single-wall radiation cross-linked XL-ETFE with tin-plated copper (150°C) for dense airframe weight savings.
- Does CASMO supply tin-, silver- and nickel-plated AS 22759 slash sheets?
- Yes — CASMO supplies a broad range of AS 22759 slash sheets spanning tin-plated (150°C), silver-plated (200°C) and nickel-plated (260°C) copper conductors.
- When should engineers choose radiation cross-linked XL-ETFE (/32, /34, /43) over PTFE (/11, /12)?
- Select XL-ETFE slash sheets for 150°C–200°C harnesses where reduced outer diameter, lower harness mass, higher scrape-abrasion/cut-through strength and better gamma-radiation tolerance are priorities. Select extruded PTFE (/11 or /12) when continuous temperatures reach 200°C–260°C or when maximum chemical inertness and ultra-low dielectric loss are required.
- Does meeting AS 22759 construction requirements automatically include NAVAIR QPL approval?
- No. Formal QPL/QPD qualification under SAE AS 22759 is administered per individual slash sheet and AWG gauge. Always confirm whether your programme requires QPL-listed traceability or commercial-equivalent wire manufactured to AS 22759 dimensional, material and electrical specifications.
Engineering Guides
- XLPE Cross-Linking Methods Compared: Electron-Beam Irradiation vs. Chemical Peroxide (CCV) vs. Silane (Sioplas & Monosil) — How electron-beam irradiation, chemical peroxide CCV curing, and silane moisture cross-linking convert polyethylene into thermoset XLPE — comparing thermal rating, wall-thickness limits, scorch risk, hot-set QC testing, and XLPE/XLPO/XLPVC/XL-ETFE wire standards.