ETFE — Ethylene Tetrafluoroethylene Insulation

Melt-extrudable fluoropolymer combining thin-wall mechanical toughness, cut-through resistance and +150°C to +200°C thermal stability for compact equipment and airframe wiring.

What is ETFE insulation?

Ethylene tetrafluoroethylene (ETFE) is a melt-processable fluoropolymer engineered for installations where PTFE or FEP is too soft and conventional thermoplastics lack thermal or chemical endurance. Compared with PTFE, ETFE offers markedly higher tensile strength, stiffness and cut-through resistance, permitting ultra-thin walls down to ~0.15 mm without compromising dielectric reliability.

Unlike fully fluorinated PTFE and FEP — which suffer polymer chain scission under ionising radiation — ETFE contains alternating ethylene units that allow controlled electron-beam irradiation to cross-link the polymer into thermoset XL-ETFE. Cross-linking elevates continuous temperature endurance from +150°C to +200°C (paired with silver- or nickel-plated copper), boosts hot cut-through and soldering-iron resistance, and delivers far higher cumulative radiation tolerance than PTFE.

With a dielectric constant of roughly 2.5–2.6, ETFE trades a modest increase in high-frequency capacitance versus PTFE/FEP (2.0–2.1) for dramatically better abrasion, dynamic pinch and scrape resistance — making it the standard lightweight workhorse across AS 22759/16–/19, /32–/35 and /41–/46 airframe harnesses as well as compact UL 1516 and UL 10086 equipment wires.

Key Material Properties

PropertyRatingNotes
Temperature+150°C to +200°CHigher in cross-linked XL-ETFE grades
Wall profileThin-wall extrudableHigh cut-through & abrasion resistance
ChemicalsBroad solvent & fluid resistanceFuels, hydraulic fluids & cleaners
FlameVW-1 / FT1 typicalInherent fluoropolymer flame resistance
Dielectric & Radiationεr ~2.5–2.6 · Cross-links under E-beamFar higher radiation tolerance than PTFE/FEP
Conductors & StylesTPC (150°C) · SPC/NPC (200°C)AS 22759/16–/19, /32–/35 & /41–/46 · UL 1516/10086

ETFE Insulated Products

  • XE150-P — AS 22759 · XL-ETFE · -65°C to +150°C · 600V
  • XE150-L — AS 22759 · XL-ETFE · -65°C to +150°C · 600V
  • UL 10086 — UL 758 AWM · ETFE · -60°C to +200°C · 600V
  • SAE AS22759/43 — AS 22759 · XL-ETFE · -55°C to +200°C · 600V
  • SAE AS22759/41 — AS 22759 · XL-ETFE · -55°C to +200°C · 600V
  • SAE AS22759/34 — AS 22759 · XL-ETFE · -55°C to +150°C · 600V
  • SAE AS22759/33 — AS 22759 · XL-ETFE · -55°C to +200°C · 600V
  • SAE AS22759/32 — AS 22759 · XL-ETFE · -55°C to +150°C · 600V
  • SAE AS22759/19 — AS 22759 · ETFE · -55°C to +150°C · 600V
  • SAE AS22759/18 — AS 22759 · ETFE · -55°C to +150°C · 600V
  • SAE AS22759/17 — AS 22759 · ETFE · -55°C to +150°C · 600V
  • SAE AS22759/16 — AS 22759 · ETFE · -55°C to +150°C · 600V
  • FLR7Y — ISO 19642-3 · ETFE · -40°C to +180°C · 25/60V

Applications & Standards Using This Material

Frequently Asked Questions

How does ETFE differ from PTFE and FEP?
Standard ETFE carries a slightly lower continuous temperature rating (+150°C vs. +200°C/+260°C) than FEP or PTFE, but delivers substantially higher mechanical toughness, abrasion resistance and radiation tolerance in thinner walls.
Where is ETFE wire commonly used?
In weight-critical aerospace harnesses (AS 22759), high-density electronic enclosures, industrial sensors, robotics and demanding instrumentation.
Why does ETFE tolerate electron-beam cross-linking when PTFE and FEP degrade?
ETFE's molecular backbone contains hydrogen-bearing ethylene segments that form stable cross-links under controlled electron-beam irradiation, converting it into thermoset XL-ETFE with enhanced heat and cut-through strength. Perfluorinated PTFE and FEP lack those C–H sites and instead break down via chain scission.
When should engineers pick ETFE over PTFE or PEEK?
Pick ETFE or XL-ETFE when you need ultra-thin-wall abrasion and cut-through durability at +150°C to +200°C with light harness weight and lower cost than PEEK. Step up to PTFE for +260°C / εr 2.0 RF loss, or to PEEK when both +260°C and 100% PFAS-free zero-halogen compliance are mandatory.

Engineering Guides