TPE — Thermoplastic Elastomer Insulation

Flexible, halogen-free elastomer spanning thin-wall automotive wires, high-flex UL AWM styles and halogen-free flat ribbon cables across 105°C to 150°C grades.

What is TPE insulation?

Thermoplastic elastomers (TPE, spanning TPE-E, TPE-S and TPV copolymer families) bridge rigid thermoplastics and cross-linked rubbers: they extrude smoothly in thin walls while delivering elastic recovery, flex life and low-temperature toughness without chemical curing. Depending on chemistry — polyester TPE-E for high heat and hydrolysis endurance, styrenic TPE-S for supple flexibility, or TPV vulcanisates for rugged jacketing — TPE spans operating temperatures from 105°C to 150°C.

Because TPE formulations are inherently halogen-free and lightweight, they are widely adopted across ISO 19642 automotive harnesses (such as FLR12Y, FLR13Y and FLR31Y), vehicle CAN-Bus jackets, compact UL 758 hook-up wires and halogen-free IDC flat ribbon cables where PVC is restricted or too stiff.

Key Material Properties

PropertyRatingNotes
Temperature−40°C to +125°C / +150°CGrade dependent (TPE-E / TPE-S / TPV)
Halogen statusHalogen-free gradesLow toxicity & environmental compliance
FlexibilityHigh flex & cold impactMaintains suppleness in tight harnesses
Typical usesISO 19642, UL AWM, Ribbon, CAN-BusThin-wall automotive & compact interconnect

TPE Insulated Products

  • UL 20674 — UL 758 AWM · TPE · -40°C to +105°C · 150V
  • UL 20346 — UL 758 AWM · TPE · -40°C to +105°C · 300V
  • UL 20297 — UL 758 AWM · TPE · -40°C to +105°C · 150V
  • UL 11856 — UL 758 AWM · TPE · -40°C to +105°C · 1000V
  • UL 11150 — UL 758 AWM · TPE · -40°C to +105°C · 300V
  • UL 10666 — UL 758 AWM · TPE · -40°C to +105°C · 600V
  • UL 10106 — UL 758 AWM · TPE · -40°C to +90°C · 300V
  • SAE J1939/15-150 — SAE J1939/15 · Foam FEP · -40°C to +150°C · 300V
  • SAE J1939/11-150 — SAE J1939/11 · Foam FEP · -40°C to +150°C · 300V
  • FLR31Y — ISO 19642-3 · TPE-S · 125°C · 25/60V
  • FLR13Y — ISO 19642-3 · TPE-E (Hydrolysis-Resistant) · 150°C · 25/60V
  • FLR12Y — ISO 19642-3 · TPE-E · 150°C · 25/60V
  • FHLR13Y — ISO 19642-5 · TPE-E (Hydrolysis-Resistant) · 150°C · 600/900V
  • FHLR12Y — ISO 19642-5 · TPE-E · 150°C · 600/900V

Applications & Standards Using This Material

Frequently Asked Questions

What is the difference between TPE-E, TPE-S and TPV?
TPE-E (copolyester) delivers higher heat and hydrolysis resistance for under-hood automotive wiring; TPE-S offers soft flexibility at lower cost; and TPV combines elastomer flex with elevated oil and thermal endurance for outer jackets.
Can TPE replace PVC in halogen-free cable designs?
Yes — TPE is a primary halogen-free alternative to PVC in UL AWM hook-up wires, automotive primary wires and flat ribbon cables where flexibility and cold pliability matter.