FEP — Fluorinated Ethylene Propylene Insulation
Melt-processable fluoropolymer combining PTFE-like chemical immunity and 200°C continuous thermal endurance with smoother extrusion, greater flexibility and long continuous lengths.
What is FEP insulation?
Fluorinated ethylene propylene (FEP) is a melt-extrudable fluoropolymer closely related to PTFE. Because FEP melts during extrusion, it produces smooth, pinhole-free insulation walls in long continuous reel lengths with greater flexibility than sintered PTFE while retaining nearly identical chemical inertness, low dielectric loss and 200°C continuous thermal endurance.
FEP is widely specified across high-temperature UL AWM hook-up wires, NEMA HP4 equipment wires, aerospace harnesses, plenum/data cabling and moisture-sealed thermocouple extension cables where chemical resistance, low smoke and clean stripping are essential.
Electrically, FEP matches PTFE's ultra-low dielectric constant (εr 2.0–2.1) and inherent UL 94 V-0 / VW-1 flame retardance while extruding smoothly as both primary core insulation and moisture-tight multi-core outer jackets — spanning UL 1330/1332 hook-up styles, NEMA HP4, plenum constructions and chemical-resistant sensor cables. For full +200°C continuous ratings, pair FEP with silver-plated copper (ASTM B298) or nickel-plated copper rather than tinned copper above 150°C–180°C.
Critical multi-core design rule: never specify an electron-beam cross-linked outer jacket (such as irradiated XLPE, LSZH XLPO or cross-linked PUR/rubber) or a high-temperature peroxide CCV jacket over FEP primary cores. Electron-beam irradiation causes irreversible C–C chain scission and brittle cracking in FEP, while 280°C–400°C vulcanisation tubes exceed FEP's ~260°C melt point; instead pair FEP cores with non-cross-linked thermoplastic jackets such as FEP, ETFE, TPU/PUR, TPE or PVC.
Key Material Properties
| Property | Rating | Notes |
|---|---|---|
| Max temperature | 200°C continuous | Fluoropolymer thermal class |
| Type | Melt-processable fluoropolymer | Long continuous extruded lengths |
| Chemical resistance | Excellent | Broad solvent, fuel & acid resistance |
| Typical uses | NEMA HP4, high-temp AWM, aerospace, sensors | Flexible 200°C fluoropolymer routing |
| Dielectric & Melt | εr ~2.0–2.1 · Melt ~260°C | Inherent UL 94 V-0 / VW-1; low-loss signal |
| Jacket compatibility | Thermoplastic jackets only | Hard No on E-beam irradiation or CCV peroxide cure |
FEP Insulated Products
- UL 1887 — UL 758 AWM · FEP · -60°C to +150°C · 600V
- UL 1333 — UL 758 AWM · FEP · -60°C to +150°C · 300V
- UL 1332 — UL 758 AWM · FEP · -60°C to +200°C · 300V
- UL 1331 — UL 758 AWM · FEP · -60°C to +150°C · 600V
- UL 1330 — UL 758 AWM · FEP · -60°C to +200°C · 600V
- SAE J1939/15-150 — SAE J1939/15 · Foam FEP · -40°C to +150°C · 300V
- SAE J1939/11-150 — SAE J1939/11 · Foam FEP · -40°C to +150°C · 300V
- NEMA HP 4 TYPE KT — NEMA HP4 · FEP · -65°C to +200°C · 250V
- NEMA HP 4 TYPE KK — NEMA HP4 · FEP · -65°C to +200°C · 1000V
- NEMA HP 4 TYPE K — NEMA HP4 · FEP · -65°C to +200°C · 600V
- FLU6Y — ISO 19642-3 · FEP · 200°C · 25/60V
- FLR6Y — ISO 19642-3 · FEP · -40°C to +200°C · 25/60V
Applications & Standards Using This Material
Frequently Asked Questions
- What is the difference between FEP and PTFE?
- Both share similar chemical resistance and dielectric properties, but FEP is melt-extrudable for smoother walls, greater flexibility and longer continuous lengths up to 200°C, whereas PTFE supports higher temperatures up to 260°C.
- Where is FEP insulation commonly used?
- In 200°C UL AWM and NEMA HP4 hook-up wires, aerospace and defence wiring, moisture-barrier thermocouple cables and low-loss instrumentation circuits.
- Can FEP insulated cores be covered with an electron-beam cross-linked XLPE, LSZH or PUR jacket?
- No — never pair FEP primary cores with an E-beam cross-linked or high-temperature peroxide CCV outer jacket. Ionising irradiation degrades FEP through backbone scission (causing brittle transverse cracking during stripping and bending), and CCV vulcanisation melts FEP (~260°C melt point). Use non-cross-linked thermoplastic jackets such as FEP, ETFE, TPU/PUR, TPE or PVC instead.
- What conductor plating is recommended for 200°C FEP wire?
- Use silver-plated copper (ASTM B298) or 2% nickel-plated copper (ASTM B355 Class 2) for continuous +200°C operation; tinned copper is best limited to ≤150°C–180°C because tin accelerates brittle copper-tin intermetallic growth near its 232°C melting point.
Engineering Guides
- J1939 Cable Impedance: Why 120Ω Is Non-Negotiable in CAN Bus & CAN FD Design — How dielectric permittivity, insulation wall concentricity, pair lay length, and shield capacitance govern 120Ω ± 10% characteristic impedance across heavy-duty SAE J1939-11, J1939-14 (500 kbps), and CAN FD vehicle backbones.
- Change Order Survival: Amending a Released J1939 CAN Bus Cable Spec Mid-Program — A practical engineering checklist for modifying J1939 CAN cable jacket chemistry, outer diameter, temperature class, or hybrid power+CAN cores mid-program without breaking connector tooling, IP69K seals, or 120Ω signal integrity.
- Fluoropolymer vs. Silicone Insulation Guide: PTFE, FEP, PFA, ETFE, PVDF & SiR Tradeoffs — How to choose between extruded/wrapped PTFE, melt-processable FEP and PFA, mechanically tough ETFE and PVDF, and ultra-flexible Silicone Rubber across chemical immersion, bend radius, cut-through, max O.D., HV corona, and 2026 PFAS strategy.
- Why FEP & PTFE Insulated Cores Cannot Use Cross-Linked Jackets: E-Beam, Peroxide, Silane, and Silicone Compatibility Guide — Real failure-analysis photos and polymer-physics guide explaining why cross-linked PUR, rubber, and XLPE jackets cause brittle cracking and fracture in FEP/PTFE primary cores — plus safe hybrid alternatives.